Every shower has a pan, even the ones that look like plain tile.
The shower pan is the floor of the shower plus everything under it that sends water to the drain. There are three main shower pan options:
- A mortar bed, sand and cement packed by hand into a slope, with a waterproof liner and tile on top
- A prefab pan, a one piece acrylic or fiberglass base that comes out of the box already sloped
- A foam tray, a pre sloped foam board with the waterproofing already bonded to it, ready for tile
For a tiled floor, a mortar bed or a foam tray is the usual choice. A prefab pan is the quick, cheaper route when you don’t need tile underfoot.
Each one tends to fail in one particular spot. Two of those spots stay hidden until the damage is done, and the third one you can feel with your feet.
Why the Shower Pan Is the Part That Fails
Shower walls shed water. The floor holds it, sometimes for minutes after every shower, and some of it seeps through the grout.
So the pan has two jobs. It has to slope toward the drain, and the standard is at least 1/4 inch per foot, according to Flooring Clarity’s guide to shower pans. And whatever water gets past the tile has to reach the drain instead of the subfloor.
A pan that fails slowly can soak the subfloor for years before a stain shows on the ceiling below. That’s why a soft floor around the shower is one of the most common surprises behind an old bathroom wall.
Shower Pan Options Compared
| Pan | What it is | Typical cost | Best for | Where it usually fails |
|---|---|---|---|---|
| Mortar bed | Hand packed sand and cement sloped to the drain, a liner, then tile | Custom tile pan $900 to $3,500 installed | Any size or shape, drains anywhere | The liner, when there’s no slope under it or the weep holes clog |
| Prefab pan | One piece acrylic or fiberglass base | $150 to $620 for the base; labor about $350 to $570 | Standard sizes, fast jobs, no floor tile | Flex and cracks when it isn’t bedded solid |
| Foam tray | Pre sloped foam with a bonded membrane, tiled over | Tray materials about $200 to $800 | Tile floors in standard sizes, light loads | The drain connection and the seams to the walls |
Costs are national figures from This Old House (updated June 2026) and Flooring Clarity’s materials table.
The Mortar Bed: Fits Anything, Fails at the Liner
A mortar bed is the old way, and a good tile setter can make it fit any shower. Sand and cement get mixed to about the feel of damp sand, packed down and screeded into a slope toward the drain.
The traditional build has two layers of mortar. A thin sloped layer goes down first, and a waterproof liner (usually a PVC or CPE sheet) goes over it and several inches up the walls. Then 2 to 3 more inches of mortar goes on top before tile, as Fine Homebuilding describes it.
That top layer gets wet. Water passes through grout, soaks the mortar and runs down to the liner, which carries it to small weep holes in the side of the drain.
Trouble starts when the liner’s laid flat on the subfloor with no slope under it. The water has nowhere to go, and Fine Homebuilding writer Tyler Grace says the soaked bed eventually weakens and molds. He’s torn out “countless” pans built that way, and he also says a pan built right shouldn’t need replacing. Weep holes packed shut with mortar during the build do the same thing.
The other cost is time and weight. You’ll wait at least 24 to 48 hours for the mortar to cure before tile or waterproofing, according to JourneymanHQ, and a packed bed can weigh several hundred pounds.
There’s a newer version, too, built with one layer. The sloped mortar goes down first and the waterproofing goes on top of it, right under the tile, so the mortar stays dry. That’s how many curbless showers get their slope.
The Prefab Pan: Fast and Cheap, Fails Underneath
A prefab pan is a molded acrylic or fiberglass base with the slope and drain hole built in. It’s the cheapest of the three. This Old House puts fiberglass bases at $150 to $450 and acrylic at $200 to $620, with about four hours of labor at $350 to $570.
The catch is what’s under it. A prefab base is thin, and it won’t hold up without full support across its whole bottom. Installation manuals tell installers to spread mortar or leveling compound over the floor and press the base down into it so every inch of the bottom touches.
Skip that bed and the base flexes a little under every step, so a shower floor that gives or creaks under your feet is the early warning of a crack. A homeowner once called The Money Pit about a corner base that cracked about a year in. The host’s answer was that a pan set in mortar “would not move.”
Prefab pans come in set sizes, and you usually can’t tile right over one. Most have a flange that the wall panels or tile sit in front of, and that joint gets sealed with silicone.
The Foam Tray: Built for Tile, Fails at the Drain and Seams
A foam tray is a sloped foam board, often with a waterproof membrane already bonded to its top, set on the subfloor in a bed of thinset. Tile goes right onto it. Fine Homebuilding calls it the simplest of the three tile options and the most predictable, and usually the most expensive in materials.
It’s light, a few pounds instead of a few hundred, and it can be ready for wall waterproofing the same afternoon. The slope is molded in at the standard 1/4 inch per foot.
Its weak spots are the joints. Flooring Clarity calls the drain to pan connection the most common leak point on any pan, and a foam tray depends on a membrane collar bonded to the drain’s flange with no gaps. Then every seam where the tray meets the wall waterproofing has to overlap and seal. Done right, the floor and walls end up as one continuous waterproof layer, and one missed corner is enough to let water under the tray.
Size can be a limit too, because a tray isn’t made to order. Trays come in common sizes like 36 by 36 or 38 by 60, and cutting much off one side changes the height at its edge.
A drain that sits a couple of inches off center because of a floor joist may rule out a standard center drain tray, according to JourneymanHQ. That’s worth checking in an older house, and the typical home in Luzerne County was built around 1960.
Which Shower Pan Fits Your Bathroom
- Tile floor, standard size shower: a foam tray or a one layer mortar bed with a membrane on top. Both keep the mortar dry.
- Odd shape, oversized or curbless: a mortar bed, because it fits whatever’s there, and it’s also the answer when the drain can’t move.
- Lowest price and fastest job: a prefab pan, set in a full mortar bed, as long as you don’t need tile underfoot.
- An old bathroom with a bouncy floor: fix the floor first. A prefab base needs solid support, and a mortar bed adds several hundred pounds, which JourneymanHQ says may call for reinforcing the framing in an older home.
Whatever pan your contractor proposes, ask which one, how it’s waterproofed, and whether they’ll flood test it before tile. The guide to shower waterproofing methods explains that test, and the overview of every shower remodel option covers the walls and the rest of the shower. 570 Remodeling’s bathroom work comes with a waterproofing guarantee, and a site visit ends with a detailed, fixed estimate for materials and labor.
Frequently Asked Questions
Is a mortar bed still the best option for a shower pan?
It’s still a good one, and it’s the most flexible, since it fits any size, shape or drain spot. But it takes skill, two days or more of curing and a correctly sloped liner. A foam tray or a one layer mortar bed with a membrane on top keeps the mortar dry and leaves less room for error.
Can tile be installed directly on a preformed acrylic shower pan?
Usually not. Acrylic and fiberglass prefab pans are made to be the finished floor, and tile won’t bond well to them. If you want a tile floor, choose a mortar bed or a foam tray built to be tiled over.
How much does it cost to replace a shower pan?
This Old House puts a new shower pan at $220 to $3,500 installed, with a prefab base near the bottom of that range and a custom tile pan near the top. Removing the old pan adds about $250, and replacing a damaged base or subfloor under a leaking pan runs another $225 to $650 by the same source.
Does a mortar bed shower need a liner?
Yes. Mortar soaks up water, so a mortar bed needs waterproofing, either a liner under the top layer of mortar with a sloped layer under the liner, or a waterproof membrane on top of a single sloped bed. Plumbing codes based on the International Residential Code also call for a water test of the pan liner, and a 24 hour flood test before tile covers it.
Is a foam shower pan better than a mortar bed?
It’s faster and lighter, and it’s easier to get right, but it costs more in materials. A mortar bed costs less in materials, fits any shape and lasts when it’s built well, but it depends far more on the installer’s skill. For a standard size tile shower, a foam tray is usually the safer bet.
Get Your Free Quote
Tell us about your project and we will get back to you with a real number for your space. No pressure, no obligation.



